Guidelines: Cleaning and Care

K.D.Brainin Founder & Director
Blog: 05.12.2019

Safety comes 1st!

Active Birth Pools  are Rated No.1 for water safety and infection control standards.

This is because the material we use (Ficore) is 5 x harder than other materials and is immune to the effects of disinfection with 10,000ppm hypo-chlorite.

Seamless one-piece construction and the absence of surface mounted metal work deny micro-organisms the environment they need to propagate.

Active Birth Pools Cleaning and Disinfection Guidelines

This is a two-step procedure – first cleaning of the pool and surround, then disinfection of the pool and surround.

  1. Prior to emptying the pool remove debris and larger particles from the water with a sieve to prevent it from blocking or obstructing the outlet.
  1. Use the standard infection control precautions (plastic apron, disposable gloves and eye protection) when cleaning the pool. Ensure the area is well ventilated.
  1. Cleaning – use a non-abrasive detergeant with non-abrasive sponge or cloth to thoroughly clean the pool. Ensure the tap is cleaned first, so as not to transfer micro-organisms from the “dirty” pool area to the cleaner tap region. Rinse well with warm water.
  1. Disinfecting – use chlorclean or similar hypochlorite disinfectant following the directions on the packet for mixing the solution to the correct concentration for disinfecting the birth pool and surround.Do not use bleach as it is highly corrosive and could cause damage to the fittings.
  1. Apply the solution to the tap and spout prior to disinfecting the pool.
  1. There are 3 methods for disinfecting the pool that are commonly used in hospitals:

1) Fill the pool with cold water and add the requisite amount of disinfectant – leave for ten minutes.

The advantage of this method is that it is 100% effective but wasteful of water, time consuming and uses a large amount of disinfectant

2) Make up 2-3 litres of solution and pour it around the inside of the rim. Then use a new disposable mop or cloth to spread the disinfectant over the surface of the pool. Leave for ten minutes.

The advantage of this method is that it is economic in terms of time and cost but relies upon the person carrying out the task to ensure that 100% of the pools surface is disinfected.

3) Fill a spray bottle with disinfectant and thoroughly spray the surface of the pool and surround. Then use a new disposable mop or cloth to spread the disinfectant over the surface of the pool. Leave for ten minutes.

The advantage of this method is that it is economic in terms of time and cost but relies upon the person carrying out the task to ensure that 100% of the pools surface is disinfected

  1. Open the drain outlet and empty the pool of the disinfectant.
  1. Using cold water, rinse the tap then the pool to remove all traces of the disinfectant, to prevent any residue being left on the pool surface.
  1. Dry the entire surface of the pool using a new cloth or disposable mop head.
  1. Keep the drain outlet closed when not in use.

Please note: If you want to use a product that is not chloride based please contact us for approval.

Damage resulting from higher water temperatures, steam cleaning or use of products not approved by Active Birth Pools will not be covered by our guarantee.

If you are duty flushing the taps with hot water/steam add 10cm of cold water to the pool first.

Important Update

Hospitals worldwide are starting to use Copper / Silver orca disinfection systems in an effort to combat bacterial issues and improve water safety.

We have discovered that there is great potential for staining with the Copper / Silver orca disinfection system

Copper-silver ionization systems introduce trace amounts of copper into the pool water.

In some cases, exposure to elevated copper levels can lead to staining of the sanitary ware and other surfaces, such as walls, floors, or fixtures.

This study goes into great detail – https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7384302/

Please note that staining caused by these systems is NOT covered by our guarantee.

If your hospital is using one of these water treatment systems we suggest that you contact the department responsible for water safety as regular monitoring and appropriate copper levels are essential to mitigate the risk of staining.

Protocols from hospitals using Active Birth Pools.

 

How to restore your old birth pool to pristine condition

We’ve been supplying water birth pools to hospitals since 1989.

Many of the pools we supplied in the 90’s are still in active service!

We occasionally receive reports that the pools are not looking as clean and bright as they originally were.

Not to worry.

There is a product called tide mark cleaner that was developed for spas and swimming pools.

You can either use it to remove stains or brighten up the appearance of the pool when necessary.

It will restore your pool to pristine condition.

Here’s a link:

http://www.amazon.co.uk/Waterline-Cleaning-removes-lines-cleaner/dp/B006DFD7VK

Related information:

 

REQUEST A QUOTE
DOWNLOAD OUR CATALOGUE

Pin It on Pinterest

Share This